Overview

Cavalier 32 Sail Plan
The Cavalier 32, affectionately known as the “Cav32”, is perhaps the best production cruiser to be produced in New Zealand, and certainly one of the most successful. Right from the get go, when Sea Spray magazine in July 1971 took the first production boat for a sail they were impressed by both the spacious interior, berthing up to eight, and its on-the-water performance; noting it was fast, responsive, incredibly close-winded and with good acceleration.

The boat went on to compete very successfully as an ocean racer with a half ton rating, eventually finding its place among the cruising community as a comfortable and reliable blue water vessel. Many have cruised the South Pacific extensively, while others have circumnavigated.

History

Designed by Bob Salthouse in 1969, the prototype Cavalier 32 made its debut at the 1970 Auckland Boat Show. The concept was for a hull with high racing potential; a boat that would be satisfying to race inshore as well as offshore, yet have family-size cruising accommodation. It immediately proved popular with 14 boats sold by the time the first boat was launched in Jul 1971.

The Cavalier 32 became the first boat offered by a relatively new partnership between John Salthouse and respected boat builder Peter K. Smith. The venture was known as Cavalier Yachts, which incidentally, at its peak in the 1970s became the largest production boatbuilder in Oceania.

Shortly after its introduction the boat’s rig was revised with a shorter mast and boom to rate under the half ton racing rule. As a half tonner, the Cav32s were formidable competition that the boat stacked up many victories in the mid-70s.

The racing tradition of the Cav32 is alive and well today, each year a team of RNZYS skippers compete with the Royal Sydney Yacht Squadron aboard Cav 32s both in Auckland, NZ and Sydney, Australia. In the 30 year history there has never been a protest; in grand Kiwi-Aussie spirit, all altercations have been settled in the bar.

The boat went on to find its niche as a favorite among the cruising community. In total 99 boats were built in New Zealand before the infamous 20% “Muldoon boat tax” decimated the NZ boatbuilding industry. The molds were exported to Australia and Japan where a similar number were built.

The Australian boats sported a redesigned rig that was 1.5m taller as well as some altered layouts.

“Bullet proof”… Andrew Fagan recounts the maiden delivery voyage of Tingara in 1975, skippered by none other than builder Peter Smith himself. The boat was caught in extreme conditions passing Castlepoint; wind speeds were clocked at a sustained 100knots with gusts of 120knots. A nearby 55ft fishing boat floundered with the loss of 2 lives while Tingara, running on bare poles, was broached and rolled multiple times by breaking waves. Remarkably the rig stayed put, and the crew did not send a mayday (the radio quit), and after riding out the rough stuff, the boat made its way into Wellington harbor a little wet inside and a some staved in washboards.

Sailing Characteristics

By modern lightweight racer/cruiser standards the Cavalier 32 is considered a substantial all rounder with excellence in heavy conditions and downwind performance. Helped by it’s 50% ballast ratio, expect to hold up full canvas well after other boats have to reef.

When Sea Spray magazine tested the boat during its debut, they described the boat being particularly stiff, “when a gust hits, the boat accelerates forward and does not lay on her ear and fight to round into the wind”. They noted the boat being fast off the wind without the tendency to broach and summed it up by saying, “At all angles of sailing the boat is superb. When ghosting she carries her way and makes miles; in the fresh she is truly exhilarating”

The boat is well balanced and easy to sail and single-hand. Expect finger light steering at all times.

Boat Configuration & Layout

The Cavalier 32 has relatively modern lines for a boat conceived in the early 1970s There is a moderately racked bow tapering out to a relatively narrow beam and a powerfully shaped aft quarter, reminiscent of successful Sparkman and Stephen cruiser/racers like the S&S34. The overhangs are nicely balanced and the sheerline attractive.

Under the waterline is a fin keel drawing 5′ 6″ and a skeg hung rudder which is controlled optionally by tiller or wheel depending on the boat. There are some shoal draft examples on the market that draw 5′ 3″ and 5′ 4″.

The cockpit has space for three and is adequately protected by substantial coamings and a coachroof that is just the right height. Side decks offer easy passage. Five crew can quite happily get about the decks in sailing mode.

Up above is a masthead rig with a small high aspect ratio main and a large genoa. A handful of the earliest NZ boats had taller rigs, as did all of the Australian built boats.

Inside, the cabin feels spacious for a 32 footer of its era with 6′ 1″ of headroom. There are twin sea-going quarter berths in the space below either side of the cockpit. The galley is small and functional on port side of the boat. Refrigeration is under the port quarter berth, which can be inconvenient to access at times. Across from the galley on starboard side is a decently sized nav station.

Further forward is the saloon with settee births on either side of the keel-stepped mast which intrudes into the cabin area, not entirely the most ideal setup for liveaboard space. The saloon table on most boats can be put away by sliding it up the mast to the cabin top.

On the other side of the forward saloon bulkhead is the head which shares space with the v-berth. On some models the head is built on the saloon side of the bulkhead subtracting from saloon space but allowing for full twin berths in the V.

Various accommodation layouts were offered with up to eight berths. The interior is finished in white, mahogany trim and mahogany veneer giving an overall feel that is light and spacious.

Construction

The boat was one of the early pioneers of cored fiberglass construction. The hull is built incredibly strong with hand-laid GRP with end grain balsa coring.

The layup from the exterior moving inwards starts with the gel coat which is reinforced by 1oz matt, then followed by 10oz cloth and two layers of 2oz matt. The balsa coring is 19mm thick in the bilge and 13mm thick above the waterline. Then comes 2oz matt and 24oz woven rove which forms a strong impact resistant layer.

All through deck fittings are backed by wood and glassed over. The hull-deck join is epoxy glued, then pop riveted with Monel rivets every 6 inches and stainless steel bolts every 12 inches. The join is glassed over forming a gusset equal to the hull thickness.

Specifications

LOA: 32′ 0″ (9.8m)
LWL: 24′ 0″ (7.3m)
Beam: 9′ 9″ (3.0m)
Standard Draft: 5′ 4″ (1.6m)
Displacement: 9,000 lbs (4072kg)
Ballast: 4,570 lbs (2076 kg)
Sail Area: 375 sq.ft. (34.85 sq.m.)

Headroom: 6′ 1″ (1.85m)
Engine: Various 12-20 hp

Designer: Bob Salthouse
Year Introduced: 1971
Builder: Cavalier Yachts, NZ

Buyers Notes

The Cavalier 32 has aged well, a testament to its strong construction. Areas of interested to prospective buyers are noted below:

  • The original boats built by Peter Smith of Cavalier Yachts had particular attention paid to preventing osmosis. It’s been noted that boats made later under licence may have had trouble.
  • To maintain the Cav32’s exceptional close-windedness, rig tensions need to be high. Some owners have overdone these leading to fatigue. Check wire terminals, rigging screws and chainplates.
  • Check mast fittings and the mast itself.
  • Check joins between the hull and bulkheads for movement, especially main bulkhead.
  • Check the chainplate knees. This is generally a very well engineered area, but also an area of very high stress.
  • Check the rudder stock, a few boats have had wear in the rudder shaft keyway, look for loose play in the tiller.
  • Leaching of zinc content of some bronze alloys in salt water is known to have shown up in some rudder stocks. Look for pinkish powder or paste on the surface.
  • Yanmar YSE 12hp single cylinder diesels were commonly fitted. Though smaller than what most fit today, it has proven to have adequate power when matched with an appropriately sized prop (not the folder race prop).

There is an active market for used for Cavalier 32s in Australia and New Zealand. Expect reasonable entry prices and good resale. As of 2010 asking prices range from $35k-60k NZD. There are the occasional examples that come up on the market that are presented in “as new” condition having undergone extensive refits and priced to match in the $70k-85k range.

Similar Boats

SHE 32
Cavalier 30

Links, References and Further Reading

» TradeABoat, Oct 2004 (p52-53), second-hand keelers review, “Cavalier 32, Tough & Seaworthy” by Andrew Fagan.
» Boating World, Jan 1993 (p132-133), “Buying Second Hand, Cavalier 32” by John Wellsford.
» Sea Spray, Jul 1971 (p27-31), Boat Test, “The Dashing Cavalier” by Staff.
» Wikipedia, Cavalier Yachts

Gallery

Cavalier 32 Sailboats for Sale

NEW! List your boat for sale right here. Pricing is $16.90 per listing until sold.

Please contribute additional information about this boat...

Add your stories, experiences, tidbits, updated information - whatever you think is useful to others.

8 thoughts on “Cavalier 32”

  1. David Manzi says:

    I am attempting to locate the production serial number of our Cav 32 -are you able to assist me on its location please.

    Also John Salthouse advises me they built 99 of these, the Wikipedia site suggests 177 – which is correct ???

    Thank you

    Dave Manzi

    1. W. L. says:

      Wikipedia is either plan wrong or they are counting the Australian built versions. Our article cites 99 in NZ and a similar number built offshore when the molds went to Australia and Japan.

  2. Gavin says:

    Am wanting to shift the mainsheet traveller to in front of the dodger do you need to strengthen the cabin top any feed back appreciated

    1. Bruce McNair says:

      Hi Gavin
      I’ve just bought Paloma, a cav32. She has the traveller already moved from the cockpit to a series of blocks in front of the dodger
      Let me know if you need any info

      Cheers
      Bruce

  3. IanCollins1 says:

    I am trying to source the sail dimensions of the Cavalier 975 or 32 as it is also referred to, in particular the working Jib.

    IanCollins1@netscape.net

    1. Guy says:

      Try Ted Siberiesen  (Sailmaker)
      Ted Silbereisen Sails
      Sail Makers–Marine – Highett, VIC
      29 Advantage Rd, Highett VIC 3190, Australia
      (03) 9555 7713 He has made Jibs andMains for at least two of the Cav 32’s at Sandringham Yacht club

    2. IanCollins1 says:

      Thanks for the advice Guy, I had overlooked this web page and just located it again  and found your response. I will make contact with the sailmaker.

      Regards,

      Ian Collins

  4. Freeasadog says:

    The australian built yacht’s were also known as a cavalier 975. You will also find in the main cabin that the headroom is actually 6’3

Leave a Reply